buy & sell, new & used machinery, machine tools & equipment

Machine Tools > Cut-off / Lasers / Flame / Plasma / Waterjet > Waterjet Cutters > Used

Used Waterjet Cutters For Sale

24 used waterjet cutter items for sale
1 | 2
Refine: Viewing 1 - 20 of 24 matches
Sort by:
Items Per Page:  20  |  50 |  100
Flow Mach 500 2060 XD 6' 6" x 20' 94,000 PSI Water Jet Cutting
$RFQ
Flow Mach 500 2060 XD 6' 6" x 20' 94,000 PSI Water Jet Cutting
Reference #43466 Flow Mach 500 2060 XD 6' 6" x 20' 94,000 PSI Water Jet Cutting System FEATURES: Flow Flowmaster PC Based CNC Control On Roll Around Console 5-Axis XD Cutting Head Hyperjet Dual Intens
  • Output Pressure: 94000PSI
  • Motor: 50HP
    13'1" x 6'6" Used Flow 5-Axis Dynamic XD CNC Waterjet Cutting System (GUARANTEED
    $109,500
    13'1" x 6'6" Used Flow 5-Axis Dynamic XD CNC Waterjet Cutting System (GUARANTEED
    Cutting Capacity 13'1" x 6'6" Maximum Operating Pressure 87,000 PSI Power 480v 3-Phase Flow CNC Controls Hyperjet 100 87,000 PSI Hyper-Pressure Intensifier Flow XD Dynamic Cutting Head 500 Lbs. Bulk
    6' x 10' Used Flow CNC Waterjet Cutting System for Foam, Gaskets, Rubber-Excellent, 1500 h
    $85,000
    6' x 10' Used Flow CNC Waterjet Cutting System for Foam, Gaskets, Rubber-Excellent, 1500 h
    Cutting Capacity 6' x 10' Rapid Traverse Maximum Up to 400 in/min Linear Straightness Accuracy +/-0.005 in/3 ft Repeatability +/-[0.0025 in.] Cutting Speed 0-400 IPM Maximum Operating Pressure 60,000 P
    6' x 12' Used Mitsubishi Suprema Waterjet Cutting System with Closed Loop Water Circulatio
    $77,500
    6' x 12' Used Mitsubishi Suprema Waterjet Cutting System with Closed Loop Water Circulatio
    Table Width 6' Table Length 12' Pump 60 HP Max Cutting Pressure 60,000 PSI Power Requirement 480/3/60 X-Axis Travel 72" Y-Axis Travel 144" Z-Axis Travel 6" WEIGHT 25,000 LBS Horsepower 50 H
    4' x 8' Used Omax CNC Waterjet Cutting Machine ONLY 1800 HOURS, Mdl. 55100, Omax Standard
    $RFQ
    4' x 8' Used Omax CNC Waterjet Cutting Machine ONLY 1800 HOURS, Mdl. 55100, Omax Standard
    Material Support Slats 4" x 1/8" Galvanized Steel Maximum Supported Material Load 400 lbs/sq ft (1,950 kg/sq meter) Electrical Requirements 3-Phase, 380-480 VAC ±10%, 50-60 Hz Noise Level Below 80 dBA a
    6'8" x 13'4" Used Omax Waterjet Cutting Machine ONLY 1,200 HOURS! Put into Place
    $RFQ
    6'8" x 13'4" Used Omax Waterjet Cutting Machine ONLY 1,200 HOURS! Put into Place
    Are you looking for a waterjet machine that will increase your profits? Omax is the answer. The OMAX 80X Series are bridge-style waterjet machines that come with many features, including IntelliTRAX, which maximizes tim
    Omax 60120 CNC Water Jet Machining Center
    $RFQ
    Omax 60120 CNC Water Jet Machining Center
    Reference #43117 Omax 60120 CNC Water Jet Machining Center FEATURES: 60,000 PSI 30 HP P3060V EnduroMAX Pump A Jet Cutting Head CAPACITY: Output ............................... 60,000 PSI Motor Size ...
    • Output Pressure: 60000PSI
    • Motor: 30HP
      FLOW MACH 2 CNC WATER JET CUTTING NEW: 2011 | IH
      $RFQ
      FLOW MACH 2 CNC WATER JET CUTTING NEW: 2011 | IH
      SPECIFICATIONS: PUMP - 30 HP TABLE SIZE - W 6' TABLE SIZE - L 10' INTENSIFIER - 60,000 PSI X - AXIS TRAVEL - (INCHES) 10' 2" Y - AXIS TRAVEL - (INCHES) 6' 6" AXIS SPEED - (X AND Y) +/- 0.
      • Output Pressure: 60000PSI
      • Motor: 30HP
        OMAX 80X EnduroMax CNC Abrasive Water Jet Cutting System
        $RFQ
        OMAX 80X EnduroMax CNC Abrasive Water Jet Cutting System
        Reference #32724 OMAX 80X EnduroMax CNC Abrasive Water Jet Cutting System FEATURES: Omax PC Based CNC Control 50 HP Enduromax 5060V Pump Closed Loop Water Recycling System Terrain Follower (Collision Sensing Fol
        • Output Pressure: 60000PSI
        • Motor: 50HP
          2008 - 6 x 12' Flow IFB612 CNC Waterjet Cutting System
          $RFQ
          2008 - 6 x 12' Flow IFB612 CNC Waterjet Cutting System
          Table Size 6' x 12' Max Cutting Pressure 60,000 PSI Pump 50 HP Equipped with: Flow Control Flow Path Flow Cut Software ** New Pump Motor ** ** 7,186 Total Hours **
          • Output Pressure: 60000PSI
          • Motor: 50HP
            2011 - Omax 60120 Waterjet
            $RFQ
            2011 - Omax 60120 Waterjet
            Table Size 6.5 x 12' Pump 40 HP Max Cutting Pressure 60,000 PSI Dimensions (approx) 18.9' x 9.2' (with Controller) Weight (approx) 6,200 lbs Equipped with: Closed Loop Digital Drive Brushless Sero Mo
            • Output Pressure: 60000PSI
            • Motor: 40HP
              2012 - Flow Mac 4-3020c Waterjet
              $RFQ
              2012 - Flow Mac 4-3020c Waterjet
              Table Size 6.5 x 10' Pump 30 HP Max Cutting Pressure 60,000 PSI Equipped with: Flow Xpert PC Paser 4 Cutting System XC Head w/Taper Compensation Ultrapierce Dynamic Contour Follower Water-Only Cutting Kit
              • Output Pressure: 60000PSI
              • Motor: 30HP
                4' x 4' Used Flow CNC Water Jet Cutting System (Good Running Condition, Guaranteed By Flow
                $67,500
                4' x 4' Used Flow CNC Water Jet Cutting System (Good Running Condition, Guaranteed By Flow
                Pump Output Rate 60,000 PSI Table Size 51.1" x 51.1" X Axis Travel 48" Y Axis Travel 48" Z Axis Travel 7" Horsepower 30 H.P. Flowmaster Version 6 Software 6 Bags Of Garnet Flow CNC Controller
                Omax Maxiem 2030 79" x 120" CNC Water Jet
                $RFQ
                Omax Maxiem 2030 79" x 120" CNC Water Jet
                Reference #31384 Omax Maxiem 2030 79" x 120" CNC Water Jet CAPACITY: Intensifier Pump Output ............... 60,000 PSI Motor Size ............................ 40 HP X-Axis Travel .....................
                • Output Pressure: 60000PSI
                • Motor: 40HP
                  6' x 12' Used Flow CNC Abrasive Dual Head Waterjet Cutting System with Flow PC Based Flowm
                  $49,500
                  6' x 12' Used Flow CNC Abrasive Dual Head Waterjet Cutting System with Flow PC Based Flowm
                  Work Envelope 144" x 78" Pump 100 H.P. Max Operating Pressure 60,000 PSI Abrasive Hopper Capacity 500 Lbs. Max Speeds 400IPM Table Size 156”x78” Flowmaster Software Package Upgrade Ver
                  240" x 120" x 36" Used Flow 6-Axis Low Rail Gantry Type Water Jet, Mdl. 1-
                  $RFQ
                  240" x 120" x 36" Used Flow 6-Axis Low Rail Gantry Type Water Jet, Mdl. 1-
                  None
                  Used EBBCO SWS Filtration System For Waterjet Machines. (CREATE ZERO DISCHARGE) Cleans Wat
                  $47,500
                  Used EBBCO SWS Filtration System For Waterjet Machines. (CREATE ZERO DISCHARGE) Cleans Wat
                  Zero Discharge Into Sewer Eliminate Discharge Of Cutting Water. Cleans To Reuse Water In A Closed Loop System. Protect Sewer Pipes And Your Mainline. Cleans Cutting Materials To Not Pollute Sewage Water System
                  2015 OMAX MODEL MAXIEM 1515 CNC WATERJET CUTTING, 50,000 PSI
                  $RFQ
                  2015 OMAX MODEL MAXIEM 1515 CNC WATERJET CUTTING, 50,000 PSI
                  SPECIFICATIONS MATERIAL SUPPORT SLATS: 4” X 14 GA GALVANIZED STEEL MAXIMUM MATERIAL LOAD: 300 LBS/SQ FT SPEED: 500 IPM INTENSIFIER PUMP: 30 HP OUTPUT PRESSURE: 50,000 PSI WORK ENVELOPE X-AXIS: 62” Y-AXIS:
                  • Output Pressure: 50000PSI
                  • Motor: 30HP
                    6' X 12' MITSUBISHI MWX4 CNC WATERJET MFG:2012 - INSTALLED:2013
                    $RFQ
                    6' X 12' MITSUBISHI MWX4 CNC WATERJET MFG:2012 - INSTALLED:2013
                    6' X 12' MITSUBISHI MWX4 CNC WATERJET MFG:2012 - INSTALLED:2013
                    2013 FLOW MACH 2B MODEL 2031B CNC WATERJET CUTTING SYSTEM, 6.5’ X 10.2’
                    $RFQ
                    2013 FLOW MACH 2B MODEL 2031B CNC WATERJET CUTTING SYSTEM, 6.5’ X 10.2’
                    SPECIFICATIONS INTENSIFIER PUMP: 30 HP, 60,000 PSI SPEED: UP TO 400 IPM CUTTING HEAD TECHNOLOGY: ABRASIVE WATERJET WORK ENVELOPE X-AXIS: 10.2’ Y-AXIS: 6.5’ Z-AXIS: 7” FEATURES 3-SIDED EASY ACCESS TO YOUR WORKP
                    • Output Pressure: 60000PSI
                    • Motor: 30HP
                      Categories:
                      • X machine tools (24)
                      • X Cut-off / Lasers / Flame / Plasma / Waterjet (24)
                      • X Waterjet Cutters (24)
                      Condition:
                      • X Used (24)
                      Manufacturer:
                      Location:
                      Price:
                      •  to 
                      1 | 2