Manufacturer - Fata Hunter
Year - 2002
Status - Installed in USA
Product - Single Coat Roof Deck Coils
Line Direction - Right to Left

General Description
Line Speed - 200 FPM (61m/min)
Width Range - 24" - 51.25"-24" (609mm - 1302mm)
Thickness Range - .027" - .054" (.69mm - 1.39mm)
Cross Sectional Area -2.77in2 (1785mm2)
Cross Section Variation (from Coil to Coil) - 25%
Yield Strength Minimum - 28,000 psi (193N/mm2)
Camber (Head & Tail) Maximum - 0.24" (6mm) in 10 ft (3.05m)
Incoming Flatness Maximum - 50 I-units
Exit/Entry OD - 36" - 72" (914mm - 1829mm)
Entry ID - 18.5" - 24.5" (470mm - 622mm)
Exit ID -18.5" - 20.0" (470mm - 508mm)
Coil Build-Up Ratio Maximum - 3.6:1
Coil Weight - 50,000 Lbs - 8,000 Lbs (3628 kg - 22676 kg)

Line Speeds
Entry Section - 250 FPM (76m/min)
Process Section - 200 FPM (61m/min)
Exit Section - 250 FPM (76m/min)
Thread - 50 FPM (15m/min)
Acceleration/Deceleration Rate - Max. 60 Ft/min/s (18m/min/s)

Strip Tensions - At maximum cross-sectional area:
Payoff - 6,089 lbs/2761 kg Tension | 2,200 psi/155 kg/cm2 Stress
Entry Accumulator- 6,365 lbs/2887 kg Tension | 1,500 psi/106 kg/cm2 Stress
Surface Treatment - 5,535 lbs/2510 kg Tension | 2,000 psi/141 kg/cm2 Stress
Oven - 6,919 lbs/3138 kg Tension | 2,500 psi/176 kg/cm2 Stress
Exit Accumulator - 6,365 lbs/2887 kg Tension | 1,500 psi/106 kg/cm2 Stress
Rewind - 14,668 lbs/6652 kg Tension | 5,300 psi/373 kg/cm2 Stress

Coatings
Solvent Coatings
Water Based Coatings - Can be processed in the system
Coating (Reference)
Top - 0.5 mils dry film (13 m)
Bottom -0.5 mils dry film (13 m)
Solids - 55% content by volume

Treatment Section
1)Cleaning - 8.0 Seconds process time
2)Brush -
3)Cleaning - 8.0 Seconds process time
4)Hot rinse - 8.0 Seconds process time
5)Phosphoric Acid - 8.0 Seconds process time
6)Hot Rinse - 6.0 Seconds process time
7)Reverse Osmosis Rinse - 6.0 Seconds process time

Accumulator Storage
Entry/Exit - 79 seconds at 200 FPM line speed (61m/min)

Coater Entry
Strip Temperature Maximum 115 degrees F (46 degree C)

Oven
Cure capability - The prime oven is designed to cure the reference coatings on

the reference strip at the maximum process line speed
Residence Time - 24 seconds in oven at maximum process line speed
Peak Metal Temperature (PMT) - 480 degrees F (250 degrees C)
Solvent Load - See Reference Data

Afterburner
Reactor Temperature Maximum - 1472 degrees F (800 degrees C)
Residence - 0.75 seconds
Destruction Efficiency - 99%

Quench Unit
Strip Exit Temperature - 130 degree F (54 degree C)

Coaters
Coater Coating Thickness Capability
Top Heads - 0.12 - 2.4 mils (3-60 m)
Bottom Heads - 0.12 - 1.2 mils (3-30 m)
Solids - 55% content by volume

Roll Schedule
Please contact our office

Utilities

Electrics
Incoming - 460 V, 3 phase, 60 Hz
Voltage Deviation - +/- 10%
Frequency Deviation - +/- 3%
A-C Motors (fixed speed) - 460 V, 3 phase, 60 Hz
PLC Input/Output - 110 V, 1 phase, 60 H

Cooling and Make-up Water
Pressure - 75 psi (5.2 bar)
Temperature - 60 degrees F (15 degrees C)
Quality - "well water"

Structured Steam
Pressure - 40 psi (2.7 bar)

Compressed Air
Design Pressure
Maximum - 120 psi (8.3 bar)
Nominal 80 psi (5.5 bar)
Design 60 psi (4.2 bar)
Air Quality - Dry and filtered

Natural Gas
Calorific Value - 1000 BTU/ft3 (8,900 kcal/Nm3)
Working Pressure - 5 psi (.34 bar)

Environment
Temperature, Ambient
Inside - 104 degrees F (40 degrees C)
Outside 41 degrees F (5 degrees C)

Relative Humidity -
Maximum 90%

Elevation
Less than 670 FT (204m)
Line is approximately 384 ft long with an approximate height of 41 feet at the

accumulators

Additional information, technical details and information can be provided upon

request

Specifications are subject to verification by the purchase

This machine is listed for sale by National Machinery Exchange Inc located in Newark, New Jersey